Jacob's Ladder

A little video to show you how it works :) ignore the noise, I had the tv on and forgot it would record... I may do more videos of how to makes with narration and put them on Youtube ! Good idea ?

Project number 2...Jacob's Ladder !

You will need, thick card or mount board about 2mm thick, patterned papers, 3 lengths of 1 metre long fairly thin ribbon i.e not grosgrain (this tends to be a bit too thick), pva glue, paint embellishments photographs or pictures etc and general craft tools i.e scalpel and mat etc


1. Using a sharp craft knife or scalpel and a metal ruler accurately cut 10 or 12 6cm by 6cm squares from the thick card or board. Put these pieces in pairs making sure each pair are the same size. If necessary re-cut some to make sure they are the same.

2. On one side of each square draw three lines, one along the centre and one on either side of the square parallel about 1 cm in from the edge...to make sure they are all the same line up the sqaures together and draw the lines in one go rather than measure and draw each square seperately.

3. Paint or cover the plain side of the squares leaving the drawn lines on the other side.


4. Take one square and place it covered side down, glue the first piece of ribbon along the centre right to the edge keeping it straight, then glue the other two pieces in the opposite direction on each side along the lines.


5. Take the other square from the pair and glue that down on top making sure all the edges are glued and that the ribbon has been pulled fairly taught but not too tight or too loose, sounds hard but it's not :) just firm ! If it is too loose or too tight it won't flip flop properly


6. Making sure you hold it down long enough to be secure flip the ribbons over the top keeping them straight and flat and taught put another square pattern side down on top of the ribbon and then repeat steps 5 and 6 until you get to the final piece.



sorry the ribbons should still be stretched over the blue spotted square in the pic below when you put the next square on top




7. Once you get to the last square, cut the outer ribbon pieces off before the edge to keep it neat, then cut the middle piece about 3 inches long off the edge and fold it back over before gluing the last piece on so that you can use it as a hanging tab !



Tip, just make sure as you go along that the edges of the ribbon are matching up so it flows properly..



8. Attach pictures, words and flat embellishments UNDERNEATH the ribbon and on the squares, DO NOT GLUE THINGS TO THE RIBBON OR ON TOP OF THE RIBBON as this will stop the ladder working !






9. Have fun and I bet you want to make more than one ...I did and you can vary the sizes and number of squares but not too much as all these changes and stop it working well.


Also lease leave a comment and let me know what you think :)

One of three projects...

This is not really a 'how to' because it is really easy and you have probably done it all before but maybe it is more of a reminder of what you can do with a bit of paint, some craft paper and a few embellishments..decorate a plain box, cigar box, chipboard box etc you can send them to someone special or use to decorate your home and they are even practical to keep things in from domestic to nuts and bolts, hair bobbles and clips or other craft materials etc etc the possibilities are endless !




The next two projects will go up this week and the second will be 'how to' make a Jacobs ladder' now these are really fun !


Also don't forget to go over to my blog www.littlemisscrafty.blogspot.com to put your name down to win one of my new heart brooches...'wandering Princess'

Project problems...

I am still having problems uploading my pictures for this project, they are too big and take ages to attempt to upload before telling me they can't ! grrrrr but i am going to borrow a different camera and definitely upload them this week...I finish work early tomorrow so this is what I will be spending tomorrow afternoon doing ! please come back and check !

Inchie pendant/clip !

Hey there, new project today is an Inchie pendant/ clip meaning it can be either or both....
Okay what you need is shown in the first photo it is basically general craft stuff as always, paper, tools and embellishments, you won't need a lot as it's very little !


1. From a sheet of 12 x 12 scrapbook paper cut two 1 inch high strips, mark each inch with a tiny dash and then fold concertina style and glue the two strips together to make one long strip.


2. Cover two 1 inch cardboard/chipboard squares and decorate.

3. On the inside of one of the squares glue down a piece of ribbon approx 6 inches long in the centre ( this will tie the book together)

4. Glue each end of the strip to the insides of the covers and tie the ribbon around the front to keep bound.

5. You can decorate the inside pages however you like with miniature photos etc....GO WILD ! and make loads.


6. Now you can glue a wooden peg to the back so that you can peg this on to books note boards etc etc or you can make a hole in the top of the back cover, add a jump ring and then a piece of cord, ribbon or a chain and wear as a pendant on a necklace or make loads and have on a bracelet !

ATC house template

Sorry it's been so long but my scanner just won't play ball so I have photographed my template please excuse the spilt tea stains !
Most of the measurements are in inches but where the size was quite small I have used centimetres, make sure that the scored sides when folded are on the outside, use brown gummed parcel tape and leave to dry before painting or covering or if you are super confident and have a really strong glue you can glue them edge to edge and hold till dry !
If you can't quite make out the sizes double click on the photo and it will go to it's original size on another window !
I have also forgotten to add the measurement of the triangle, from the 3 inch wall height it is a further 3 cms then the line for the fold of the roof...

Sugar edge decorations

From my blog I have put a short 'how to' make here for the coloured ruff hanging decorations.

You will need:
cardstock or decorative papers
selection of paper punches
decorative edged scissors
glue
string
embellishments
glitter
needle and thread
coloured crepe paper/ streamers

1. Firstly Cut a length of crepe paper roughly 2 inches wide and 1 metre long and cut one of the long sides with the decorative edge scissors.

2. Using the needle and thread use a loose tacking stitch on the straight edge the push all the paper to the anchored stitch ( the first stitch) and pull into a circle and stitch both edges together.

3. Dab some glue along the outside edge of the ruff and then shake over glitter, leave all to dry.

4. While they are drying punch out circles from the papers and cardstock and embellish how you like just make sure to make 2 for each ruff so one goes on each side.
Also cut lengths of string and knot into a loop to hang decorations by.

5. When dry glue both embellished circle pieces one to each side but don't forget to lay a knotted loop to one side of the decoration before gluing a side on.

Hang up and make as many as you like :)


Don't forget you can change all the colours and materials and make some really lovely ones for any occasion or just to decorate your room or even for easter ....